Metal Roof Coating & Painting in Wichita Falls, TX

Metal Roof Coating & Painting Wichita Falls

Wichita Falls sits on red clay and sandy loam along the Wichita River, and the sun here hits metal roofs hard from April through October. Add big spring hailstorms, straight-line winds and dust-orange sunsets, and a standing seam or R-panel roof that looked sharp ten years ago starts to chalk, fade and show surface rust. Metal Roof Coating & Painting in Wichita Falls restores that roof instead of replacing it. We prep the panels, treat the rust and apply a reflective coating system that adds 10 to 15 years of service life. For homeowners in Burkburnett, Iowa Park and Henrietta, that means no tear-off, no dumpster in the drive and a cooler attic by August. If your panels are still sound, coating beats replacement on cost every time. Start with a metal roof inspection so we can tell you honestly which way to go.

Why Metal Roof Coating Matters on Wichita Falls Roofs

This is one of Texas' hardest hail corridors, and the sun is just as rough. A bare Galvalume or painted panel roof on a 1970s brick ranch in Southwest Wichita Falls takes UV all summer, then gets hammered by spring storms. The paint film chalks, the cut edges and screw heads start to rust, and the panels lose reflectivity. Coating stops that slide before it turns into leaks.

It restores the reflective finish so the roof sheds summer heat instead of soaking it into the attic.
It seals surface rust and stops it from eating through panel thickness at the laps and fasteners.
It brings back a uniform color on faded panels that make a house look older than it is.
It buys 10 to 15 years before you need a metal roof replacement.

On the acreage shops and oilfield-era buildings around Electra and Holliday, coating is often the only sensible move: the structure is solid, the panels are dirty and faded, and a full re-roof does not pencil out.

Key info: A 1980s two-story brick home off Midwestern Parkway had chalky, rust-streaked panels and a 130-degree attic. We coated it with a reflective system in two days, and the homeowner measured a real drop in attic temperature that same summer. No tear-off, no dumpster.

Roofing permits and inspection rules vary by jurisdiction in this area, so confirm requirements with the local building department before any coating or repair work is scheduled. You can check the City of Wichita Falls permit information at wichitafallstx.gov.

How We Coat a Metal Roof in Wichita Falls, Step by Step

Coating only works if the prep is right. We do not roll paint over dirt, chalk or rust and call it done. Every job starts with a wash, then a rust assessment, then a coating system matched to the panel type and the amount of sun and storm exposure the roof sees.

We inspect the panels, seams and fasteners, and we check for active leaks before coating anything.
We pressure-wash the roof to strip chalk, dust and biological growth so the coating can bond.
We treat rust spots with a converter and prime bare metal and fastener heads.
We replace failed screws and washers as part of the prep, because coating over a bad fastener traps the problem.
We apply the reflective coating system in the recommended mil thickness and cure window.
We walk the roof with you at the end and hand over care instructions.

If the inspection turns up loose screws across a large panel run, we fold screw replacement and re-fastening into the same visit so the coating goes on over sound hardware.

Key info: On a metal barn outside Iowa Park, the south slope was chalked white and the north slope still looked new. We coated both slopes anyway, because a half-coated roof fades unevenly and the customer ends up paying twice. One system, one color, one cure.

Coating Approaches We Use on Wichita Falls Metal Roofs

Not every metal roof takes the same coating. Exposed-fastener R-panel and corrugated roofs, standing seam, stone-coated steel and older painted panels all behave differently under sun and hail. We match the system to the panel and to how the roof is used.

Approach	Description	Best for
Reflective elastomeric coating	Flexible acrylic coating that expands and contracts with the panels and reflects solar heat.	Painted R-panel and corrugated roofs on homes and shops.
Rust converter plus primer	Chemically converts surface rust to a stable layer before topcoat goes on.	Older panels with rust at laps, cut edges and fastener heads.
Direct-to-metal acrylic system	Single-component coating with strong adhesion and color retention.	Faded but structurally sound panels with little or no rust.
Color-restore topcoat	Finish coat that brings back a uniform color and a factory-like sheen.	Homes where appearance matters as much as heat reflection.

We tell you which system fits your roof after we see the panels, not before.

Metal Roof Coating & Painting Cost in Wichita Falls: What to Expect

Most coating jobs here start around $2.50 per square foot, and the final number depends on roof size, panel condition, how much rust we have to treat and how steep or cut up the roof is. A simple gable on a brick ranch in Faith Village sits at the low end; a two-story with valleys, dormers and heavy rust pushes toward the top. We do not quote from the driveway.

Getting two or three estimates is smart on any roof coating job. Ask each contractor what prep is included, what coating product they use and how many coats they apply. A low bid that skips the wash and rust treatment will fail early, and you will pay twice. Our full pricing overview lays out how we build a number so you can compare apples to apples.

Metal Roof Coating & Painting Near Me: How to Pick a Contractor Near Wichita Falls

When you search for metal roof coating near me, you will get a long list. Narrow it down by asking real questions before anyone gets on your roof. A contractor who cannot answer them clearly is not the one you want coating a roof you plan to keep for another 15 years.

Confirm the company is licensed and insured, and ask for a certificate of insurance before work starts.
Get at least two or three written estimates that spell out prep, product and number of coats.
Ask for local references on metal roofs, not just shingle jobs, and call them.
Check whether your neighborhood or HOA has design or color rules that affect the coating color.
Ask who handles permits if the job scope crosses into repair or panel work, and confirm with the local building department.

If the answers are vague, keep looking. You can reach us through our contact page and we will walk your roof, explain what we see and give you a written scope before you decide.

Metal Roof Coating & Painting in Wichita Falls: Pricing Guide

Service	Price	Details
Reflective coating on sound panels	Starting at $2.50/sq ft	Includes wash, rust spot treatment and one reflective topcoat on standard R-panel or corrugated roofs.
Rust treatment and primer system	Starting at $3.25/sq ft	Adds rust converter, bare-metal primer and fastener prep where corrosion has started at laps and edges.
Two-coat color restore system	Starting at $4.00/sq ft	Base coat plus color topcoat for faded panels where appearance and heat reflection both matter.
Complex or steep roof	On estimate	Two-story roofs, dormers, valleys and cut-up panel layouts need an on-site look before we quote.
Travel	Included	In Wichita Falls and surrounding areas, no separate call-out or mileage fee.
Estimate	Free	Response within 24h at (940) 400-3876, no obligation to book.

Indicative pricing, the exact cost depends on square footage, finish, and site access. Free personalized estimate within 24h at (940) 400-3876.

Metal Roof Coating & Painting: service areas

📍 Wichita Falls 📍 Burkburnett 📍 Iowa Park 📍 Holliday 📍 Electra 📍 Henrietta 📍 Archer City 📍 Olney 📍 Bowie 📍 Nocona 📍 Seymour 📍 Vernon 📍 Jacksboro 📍 Scotland 📍 Petrolia 📍 Windthorst

Frequently asked questions: Metal Roof Coating & Painting in Wichita Falls

How much does metal roof coating and painting cost in Wichita Falls?

Most jobs start around $2.50 per square foot for a standard reflective coating on sound panels. Rust treatment, a second color coat, steep pitch and two-story access push the number up. A simple ranch roof in Iowa Park will land near the low end, while a cut-up roof in Southwest Wichita Falls runs higher. We give you a written scope after we walk the roof.

Can you coat a metal roof that already has rust on it in Wichita Falls?

Yes, as long as the rust is surface rust and the panel has not rusted through. We treat the rust with a converter, prime the bare metal and fastener heads, then apply the coating system. If we find panels that are rusted through or thin at the laps, we tell you straight and talk about repair or replacement instead of coating over a problem.

How long does metal roof coating last in the North Texas sun?

A properly prepped and applied coating system typically gives 10 to 15 years before it needs a recoat, depending on sun exposure and storm wear. South and west slopes take the most UV and may chalk sooner. We use coatings made for direct-to-metal exterior use, not interior paint, and we apply them at the manufacturer's recommended thickness.

What is the best time of year to coat a metal roof in Wichita Falls?

Late spring and early fall are ideal because temperatures are moderate and the coating cures evenly. Summer works if we start early, since panels get too hot to coat by mid-afternoon. We avoid days with rain in the forecast, because the surface has to be dry and stay dry through the cure window. Spring hail season is when we see the most storm-related damage, so schedule coating before the storms hit if the roof is already faded.

Does coating a metal roof really lower attic heat in Wichita Falls?

It does. A reflective coating bounces solar heat off the panels instead of letting it soak through into the attic. Homeowners on brick ranches across Northwest Wichita Falls often notice the difference in July and August, when attic temperatures climb fast. The effect is strongest on bare or dark panels that have lost their original finish.

Do I need a permit to coat my metal roof in Wichita Falls?

Coating and painting alone usually do not require a roofing permit, but repair work folded into the job might. Rules vary by jurisdiction, so confirm with the local building department before work starts. If your home is in a historic district or an HOA, check design and color rules first. We can point you to the right office and tell you what our scope covers.

How is coating different from replacing my metal roof?

Coating restores the surface and extends the life of panels that are still structurally sound. Replacement tears off the old roof and installs new panels. Coating costs far less and avoids landfill waste, but it cannot fix panels that are rusted through, loose at the seams or storm-damaged beyond repair. We inspect first and recommend the option that actually makes sense for your roof.

Do you handle emergency metal roof coating or repair in Wichita Falls?

We respond to storm damage and active leaks as fast as we can, often within 24 hours. Coating itself is a planned job, but if a storm opens a seam or tears a panel, we can secure the roof first and schedule the coating after. Call (940) 400-3876 and describe what you are seeing.

Is the estimate really free and no obligation?

Yes. We walk the roof, check the panels and fasteners, and give you a written scope with a price. There is no charge for the estimate and no pressure to book. If coating is not the right call for your roof, we tell you that too and explain the alternatives.

Are you licensed and insured for metal roof coating in Wichita Falls?

Yes. We carry liability insurance and workers' coverage, and we can provide a certificate of insurance on request. Ask any contractor you are considering for the same document before they start work. It protects your home and your wallet if something goes wrong on the roof.